super-lightweight design for downriggers and large diameter stainless wire bail which results in less line wear and smoother releases.
Features a super-lightweight design for kites or outriggers and large diameter stainless wire bail which results in less line wear and smoother releases. The OC-1 Outrigger release clip should be attached directly to the outrigger halyard without the use of swivels. The adjustment-slider end of the…
The AFTCO Flat Line Clip, with a 135-lb. coated stainless steel cable and heavy duty snap-swivel attached, can be rigged from the stern of the boat to put trolling lines into the water at a lower angle, helping to minimize the tangling that might otherwise occur when trolling with multiple lines,…
Great for hunting, fishing, boating, camping. Resists rot and mildew.
A real space-saver. Excellent for small spaces. Vertical design holds up to 6 rods. Features durable polypropylene construction and foam grip pads that won't mar rod finish.
Stores 6 rods neatly and securely. Corrosion proof. Foam grip pads. Durable and lightweight. Comes in black.
The clip simply threads on the downrigger or kite line and is held in position with a crimped sleeve, split shot, barrel swivel, or even a simple knot in the line. Made of nylon, brass and stainless steel.
Designed to keep outrigger line and fishing line from fouling and give a clean release. Use with outrigger, downrigger and kite. Made of nylon, brass and stainless steel.
Black with pre-drilled clips #5,#7 Swivels & Snap Swwivels.
A multi-use tool that will remove all twist-in drain plugs, while also having a built in compartment to hold spare drain plugs or the one you just took out of the boat in addition to being a floating key holder. The features and benefits of this little drain plug wrench that will make boating…
Waterfowl Wading Systems Max-4 Neoprene Bootfoot Waders - Max-4 Bootfoot waders are made of 3.5mm neoprene with a 600 gram Thinsulate Bootfoot. Featuring a front hand warmer pocket with storage will provide warmth and protection in even the most severe weather.
Made of quality 100% US rubber materials that won't melt or crack under the most adverse conditions. Whether you are rigging up bally hoos, troll lures off shore or dropping your favorite bait on a down rigger, Calcutta has the right rubber band for you.
Assorted colors. 8 per pack.
Made of heavy duty high impact plastic and are UV resistant. These stops will prevent your outrigger rigging from getting tangled in your outrigger guides.
Zinc-rich cold galvanize touch up. Fights rust and rust creepage. Offers the protection of expensive hot dip galvanizing.
The S-10 Down-East Salty Rod Holder is equipped with a double clamp easily reversed for alternate mounting positions. These versatile clamps allow you to mount and remount the rod holder in a wide variety of places and are easily secured with a firm turn of the thumb screws.
The Economy Anchor features a single piece crown construction enhancing the strength of the anchor, a fluke strengthening break which provides more rigid penetration and a slip-ring design for retrievability. Each model is identified with the model number clearly marked in the fluke. The Economy…
These are great for drying wading boots, great for drying waders, and features metal construction will hold most waders boots.
1-3/4" Clamp-on Blk
Deluxe Boot Hanger
Single Tube (12") long with mounting pad and stainless hardware. For mounting on boats, truck tool boxes and bumpers. Bright anodized finish.
Hardware and stabilizer bar included. 2" hitch adapter, stainless. Adapts 4 and 6 holder rod racks.
Mounting on Center Consoles, back of seats, truck toolboxes, and bumpers. (12") long tubes with unbreakable nylon rod tube caps. Bright anodized finish. Stainless mounting hardware included.
2" Offset Receiver Hitch adapter. Stabilizer bar with hardware included. Lifts Rod Rack 6".
Console rack, boat rod holder. Anodized aluminum to withstand weather conditions. Six (6) rod holders. 12" long. 2" pipe. 2-1/2"H × 31-1/4" long hole center distance. Easy installation with four (4) Stainless Steel bolts and locking nuts. Hardware is included.
Rod holder can be mounted directly to vehicle bumper, tool boxes, or can be 2" receiver mountable front or rear of vehicle. 2" receiver adapter sold separately. Bright anodized finish. Stainless mounting hardware included.
Same as the 4 rod holder with 2 additional rod tubes. Bright anodized finish. Stainless mounting hardware included.
Surface Mountable To Suitable Areas . Bright Anodized Aluminum Finish. Mounts to Truck Tool Boxes/ Boat Transoms/T-Tops. Nylon Rod Tube Caps. 17" tube length X 49" Mount plate width. (2) 3" X 4" Mount Plates.
2" Receiver Ready / Front Or Rear. Anti-Rattle Device Included. Bright Anodized Aluminum Finish. Nylon Rod Tube Caps. 2 " Front or Rear Required (Not Included). 6" Vertical Height Adjustment.
Rod holder with fold down cooler rack carries up to a 54 quart marine cooler. Mounts either directly to vehicle bumper or 2" receiver hitch. Adapter part #204 & #174 are sold separate. Bright anodized finish. Stainless hardware included.